Видео

100% WORKS!! I tried it on my condo's underground parking spot with a pond of power steering fluid. You don't necessary need a brick, any rock is fine. And if you use the cat litter that has bleach in it, it whitens the concrete as well.. 😁😁😁 Old method is always the best method, wisdom passed down by elders!!

The point at which you take out the Dremel , can't you just install a Butterfly hinge and not cut into the door anymore?

🤦‍♀ A router. Okay. *continues to chisel because I do not own a router or this...router*

As long as you use OEM Toyota part's from what the Manuel suggest is what matters. Never use Aftermarket parts on these Toyota's!

Those dremel attachment is more expensive than corded router ! (without the dremmel itself)

My dad told me the same always lubricate the new oil filter rubber with the oil. He never explained why but I do it anyway. Thanks for the vid just got a 2004 Toyota Tacoma and wanted to know exactly where the plug and filter was.

Thanks a lot for making this video. Helped a ton! Note// I put my hand inside a grocery bag then slowly backed out drain plug til free.

Idk y they cant sell the door pre cut fully already

no way i know that lil baby dude

It is a good thing she is so so so smart! Lololololol

Bahahahaha. When he said that terrible I hollered😂.

You’re bad at this.

You replaced a door because of a small hole?

What Dremel bit do you use?

amateur night LOL

Which tip do you use?

Does removing that plate reduce the structural integrity of the car?

Or you could have just repaired the old door .....

Where is "right there" please? Where are we? Can you post in the description or in the comments what exactly you did please? What you removed to see it, the location etc?

WELL DONT HAVE EITHER!! AND DREMEL IS WAYYY TOO EXPENSIVE!!! HF HAS SUPER GREAT SELLS ON THEIRS WITH AN ENTIRE KIT!! HOPE TO GET THAT BUT DONT AT PRESENT! BUT I DO HAVE A MTOT SO HAS ANYONE TRIED USING ONE OF THESE ON SLOW FOR THIS?? Just asking because I do have one of these! Seems to me they could work well for this!? Thinking of maybe trying sample cuts on some old pieces of 2x4 just to see!?

What’s a warm start and a cold start

A speed square would've done you well in the beginning

What do you do if your husband threw the old door away? I have no idea how to go about measuring for the hinges on the new door

What RPM’s and which bit?

This is such a dumb video… he advertised it like this is easier! All the things he said we don’t need are all the things we have lying around! It’s less likely we have a dremel lol. Retarded

Im sorry to ask. I tried to read some comments, but couldn’t find the answer and didn’t understand what’s the name of that product. Can someone help me out? Tx so much

Well oh well that sure doesn’t look like it came from the factory

Hmmm, that’s the worst example of hinge mortising I’ve ever experienced.

Thank you

6:00- His alternative - a dremel

Good to have. Great machine

Dude that’s the blackest oil I have ever seen WOW.

what an awful fucking video

Heard something about putting synthetic oil and swapping back to standard will blow your motor, anyone know if this is true?

What a fucking joke…. Clickbait bitch

You need to remove this video cuz I don't even know where you're working at and the whole point of watching video is a figure out where it is I know how to use a wrench

For the whole 2 doors I'm gonna be putting hinges I'll just grab the wood chisel off the pegboard over my workbench and a hammer

My adventure with woodworking started with Woodglut.

Good idea! I am changing out a door at the end of a bathroom remodel in my home. I did not want to trust myself with a chisel, and I did not want to buy a router that I will likely never use again. This thing will attach to my dremel and 6 years after the video was made, now sells for 25 bones on Amazon. Perfect solution. Thanks!

!! Use a try-square or combination square!! The lines you made with your level could end up WAY OFF.

Why wouldn’t you just measure for the hinges instead of using a level?

You suck at this too. What an absolute pigs ear of a job. I'll never get that time back will I? Hideous

I have a hammer, I have chisels, I have 2 routers, I even have a rotary tool. I dont have a router base.

Nice

Just use the Ryobi jig. You would be done already. No Brainer.

The "agh!" Let's me know all I need to know. I'll continue to use my hinge templates and router 🤣

Quite wacky. May i say Goofy.

that kid (brooks) probably stinks

I hadn't started mine in 5 or 6 years. I checked the oil level (it was full), added fresh gas and it started on the first pull. VDO on my channel.

U.also suck.with.dremel ....blames on camera hahaha